Directed Electronics Concept 550 Bedienerhandbuch

Concept 550OOwwnneerr’’ss GGuuiiddee

7© 2004 directed electronics, inc.While the system is armed, the LED status indicator will flash approxi-mately once per second showing that the syste

8zDigital dual zone radar sensor will protect the interior of thevehicle and it’s contents with an invisible perimeter of pro-tection.disarmingTo disa

9© 2004 directed electronics, inc.the siren has been sounding, press on the transmitter to stop thetrigger and return the unit to the armed state. Th

© 2004 directed electronics, inc.5. The lights will flash four more times; the sensor warn awayand full trigger zones are now bypassed.6. The sensor z

11© 2004 directed electronics, inc.disarm/valet modeEntering your pin code using the PlainView 2 Valet switch allows youto disarm the system or enter

12transmitter valet modeThe operations described in this section refer to transmitter buttons.Remember, the buttons used in all the instructions in th

13© 2004 directed electronics, inc.multiple event total recallThis will report the last eight system triggers.1. Press and hold of the PlainView 2 Va

14Doors are covered by FACT II differently; if the alarm is triggered by anopen door for three full cycles, the doors will be bypassed until the trig-

15© 2004 directed electronics, inc.diagnosticsThe microprocessor at the heart of your security system is constantlymonitoring all of the switches and

16arm/disarm diagnostic charttable of zonesThe zone number is the number of LED flashes used by the system toidentify a specific input. The standard i

i© 2004 directed electronics, inc.limited lifetime consumer warrantyDirected Electronics, Inc. ("Directed") promises to the original purchas

17© 2004 directed electronics, inc.anti-code grabbing (ACG)This unit features Anti-Code Grabbing (ACG) with Random CodeEncryption. This means the rece

18power saver modeYour system will automatically enter Power Saver Mode while armed orin Valet Mode, after a period of time in which no operation has

19© 2004 directed electronics, inc.zArming/disarming confirmation siren chirps on or off.zAuto-Lock on/off/rpmON: The doors will lock three seconds af

20zAdd or remove remote controls.zChange PIN code.zCustom configure the remote control.zRemote valet on or off.zAutostart with low battery voltage or

21© 2004 directed electronics, inc.3. Hold/Chirp/Release - After entering the PIN code, press andhold until a chirp is heard and the LED turns on, th

22user selectable features* This feature is only available with optional IntelliStart connected.** This feature is only available with optional Smart

23© 2004 directed electronics, inc.auto (passive) arm - on/offzOn: When the system sees the ignition turn off and the lastprotected entry (door, hood,

24auto (passive) arm and lock - on/offzOn: The doors will lock when the system passively arms. Thisfeature only applies when passive arming is program

25© 2004 directed electronics, inc.fact II on/offzOn: The alarm will bypass for 60 minutes if zones 1, 3, and8 are triggered three times within a one

26auto start setting - off/battery only/temp only/battery and tempzThis feature is only available with the IntelliStart option.zOff: The vehicle will

iiLOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE,THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE C

27© 2004 directed electronics, inc.accessory b outputThe transmitter channel programmed into this feature will activate theaccessory output.silent mod

28pin programmingA PIN code can have one to four digits; each digit can be from 0-9. Programming Procedure1. Enter the feature location in the install

29© 2004 directed electronics, inc.PIN Code Confirmation ProcedureBegin this procedure within 15 seconds of finishing the programmingsequence or the n

30zTurn ignition on and press the arm/disarm button.zArm the alarm and then disarm the alarm.zTurn the ignition on and enter the system valet/PIN code

31© 2004 directed electronics, inc.adjusting the proximity sensorIt is recommended that adjustments be performed away from fluores-cent lighting, larg

32zPress of the remote control to decrease sensitivity.zThe sensor Primary zone can be tested at any time dur-ing adjustment and will generate 1 sire

33© 2004 directed electronics, inc.glossary of termsControl Unit:The "brain" of your system. Usually hidden underneaththe dash area of the v

34Warning Zone Response:Lighter impacts or movement close to the vehi-cle will generate the Warning Zone response. It consists of a warningsiren blast

35© 2004 directed electronics, inc.health checkDirected Electronics recommends you return to your installing Clifford deal-er to have your system chec

Vista, CA 92081www.directed.com© 2004 Directed Electronics, Inc. - All rights reservedG909620 08-04The company behind this system is Directed Electro

1© 2004 directed electronics, inc.limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . .itrademarks and copyrights . . . . .iiwh

what is included zControl module and harnesszTwo five-button transmitterszPresentation envelope and quick reference cardzTwo window decalszXHF antenna

3© 2004 directed electronics, inc.system maintenanceThe system requires no specific maintenance. Your transmitter is pow-ered by a miniature 3V lithiu

4transmitter configurationnnoottee::This manual describes the features and accessories that areincluded with your system along with information about

5© 2004 directed electronics, inc.transmitter functionsThis system uses computer-based code learning to learn the transmitterbuttons. This makes it po

6Button, then ButtonAccessory C output is controlled by these buttons.Button twice, then ButtonThese buttons activate remote valet.Button twice, the