Directed-electronics Automate 552 Bedienungsanleitung Seite 1

© 1999 Directed Electronics, Inc. Vista, CA N552A 12-99Model 552Installation Guide®®Downloaded from: http://www.guardianalarms.net

10 © 1999 Directed Electronics, Inc. Vista, CAAn accessory wire will show +12V when the key is in the accessory and run positions. It will not show +1

© 1999 Directed Electronics, Inc. Vista, CA 11wiring the control unitThe wiring harness supplied with this unit is the standard 12-pin harness used by

12 © 1999 Directed Electronics, Inc. Vista, CAheavy gauge relay satellite wiring diagram____________________________________(H2) harness auxiliary con

© 1999 Directed Electronics, Inc. Vista, CA 13primary harness (H1), 8-pin connectorThis wire supplies a (-) 500 mA ground as long as the system is arm

14 © 1999 Directed Electronics, Inc. Vista, CASending a negative pulse to this wire will initiate the remote start sequence. This wire can be wired to

©1999 Directed Electronics, Inc. Vista, CA 15This wire supplies a 200 mA (-) output that can be used to honk the vehicle horn. It outputs a single pul

16 © 1999 Directed Electronics, Inc. Vista, CArelay satellite key switch interfaceThe five heavy gauge wires leading from the relay satellite are used

© 1999 Directed Electronics, Inc. Vista, CA 17harness 2 (H2), 2-pin auxiliary plugConnect this wire to the wire in the vehicle that sends the signal t

18 © 1999 Directed Electronics, Inc. Vista, CAThis wire sends a negative pulse every time the remote start is activated. This can be used to pulse the

© 1999 Directed Electronics, Inc. Vista, CA 19This wire MUST be connected to hood pinswitch. This input will disable or shut down the remote start whe

2 © 1999 Directed Electronics, Inc. Vista, CAtable of contentsWhat Is Included . . . . . . . . . . . . . . . . . . . . . 3Warning! Safety First . . .

20 © 1999 Directed Electronics, Inc. Vista, CAneutral safety switch interfaceSome vehicles combine the column shift mechanism and the mechanical neutr

© 1999 Directed Electronics, Inc. Vista, CA 21IMPORTANT! Once the interface is complete, attempt to remote start the vehicle with the doorclosed and

22 © 1999 Directed Electronics, Inc. Vista, CApre-1996 dodge dakota pickups with 2.5 liter motors

© 1999 Directed Electronics, Inc. Vista, CA 23plug-in LED and valet/program switchThese plug into the module. The status LED plugs into the small two-

24 © 1999 Directed Electronics, Inc. Vista, CAThe system can control this type of system directly, with no additional parts. The switch will have thre

© 1999 Directed Electronics, Inc. Vista, CA 25This system is common in many Toyota, Nissan, Honda, and Saturn models, as well as Fords with the keyles

26 © 1999 Directed Electronics, Inc. Vista, CAInterfacing with a reversing polarity system requires either two relays or one 451M Door Lock Relay Sate

© 1999 Directed Electronics, Inc. Vista, CA 27In order for this system to control one or more aftermarket actuators, a 451M Door Lock Relay Satellite

28 © 1999 Directed Electronics, Inc. Vista, CAThese door locks are controlled by an electrically activated vacuum pump. Some Mercedes and Audis use a

© 1999 Directed Electronics, Inc. Vista, CA 29internal programming jumpers This jumper is used to determine the light flash output polarity. In the (+

© 1999 Directed Electronics, Inc. Vista, CA 3what is included6-pinminimolexplug5-pinRelaySatelliteHarness2-pinorange auxiliaryplug2-pinmicroLEDplug2-p

30 © 1999 Directed Electronics, Inc. Vista, CAtransmitter/receiver learn routineThe system comes with two transmitters that have been taught to the re

© 1999 Directed Electronics, Inc. Vista, CA 31system's memory. It can also be used to start from scratch if the transmitter buttons were programm

32 © 1999 Directed Electronics, Inc. Vista, CAtach learning1. Start the vehicle with the key.2. Within 5 seconds, press and hold the Valet/Program swi

© 1999 Directed Electronics, Inc. Vista, CA 331. Key. Turn the ignition on and then back off. 2. Select Menu. Press and hold the Valet®/Program switch

34 © 1999 Directed Electronics, Inc. Vista, CAtThe learn routine will be exited if: The ignition is turned on. The Valet/Program switch is pressed t

© 1999 Directed Electronics, Inc. Vista, CA 35feature descriptionsThe features of the system are described below. If the system is being programmed wi

36 © 1999 Directed Electronics, Inc. Vista, CA1-5 DOOR LOCK PULSE DURATION: Some European vehicles, such as Mercedes-Benz and Audi, require longer loc

© 1999 Directed Electronics, Inc. Vista, CA 372-2 TACH WIRE SENSE/VOLTAGE SENSE: If the tachometer signal wire is used, this feature must be left in t

38 © 1999 Directed Electronics, Inc. Vista, CAshutdown diagnosticsThe unit has the ability to report the cause of the last shutdown of the remote star

© 1999 Directed Electronics, Inc. Vista, CA 39valet modeTo enter or exit Valet® Mode with the Valet®/Program switch:1. Turn the ignition on and then o

4 © 1999 Directed Electronics, Inc. Vista, CAwarning! safety firstThe following safety warnings must be observed at all times: Due to the complexity

40 © 1999 Directed Electronics, Inc. Vista, CATimer Mode can also be exited manually as follows:1. Make sure the remote start system is not operating

© 1999 Directed Electronics, Inc. Vista, CA 41 If the starter does not engage, the test is complete. Once the system passes the three tests, the vehi

42 © 1999 Directed Electronics, Inc. Vista, CA The remote start will activate but the starter never engages.1. Check for voltage on the purple starte

© 1999 Directed Electronics, Inc. Vista, CA 5installation points to rememberIMPORTANT! This product is designed for fuel-injected, automatic transmiss

6 © 1999 Directed Electronics, Inc. Vista, CAEnsure that the location you pick for this switch has sufficient clearance to the rear. The switch should

© 1999 Directed Electronics, Inc. Vista, CA 7If the starter kill relay or its connections are immediately visible upon removal of the under-dash panel

8 © 1999 Directed Electronics, Inc. Vista, CAThe ignition wire is powered when the key is in the run or start position. This is because the ignition w

© 1999 Directed Electronics, Inc. Vista, CA 9Most vehicles use a (+) parking light circuit. The (+) parking light wire is often found near the light s