Directed Electronics 417 Installationsanleitung

© 2000 Directed Electronics, Inc. Vista, CA N417A 9-00®Model 417Installation Guide®Downloaded from: http://www.guardianalarms.net

10 © 2000 Directed Electronics, Inc. Vista, CAmaking your connectionsWhen connecting the security system’s wires to the vehicle wires it is important

© 2000 Directed Electronics, Inc. Vista, CA 111. Using your wire strippers and razor knife, strip approximately 1/2-inch of insulation off the wire to

12 © 2000 Directed Electronics, Inc. Vista, CAprimary harness (H1) wire connection guideThis section of the installation guide describes in detail the

© 2000 Directed Electronics, Inc. Vista, CA 13IMPORTANT! Never interrupt any wire other than the starter wire.NOTE: If connecting the H1/1 wire to con

14 © 2000 Directed Electronics, Inc. Vista, CAH1/3 WHITE/BLUE (+) TRUNK RELEASE, SENSOR SHUNT INPUTThis input is used to bypass sensor inputs when the

© 2000 Directed Electronics, Inc. Vista, CA 15H1/6 BLUE (-) INSTANT TRIGGER, ZONE 1This input will respond to a negative input with an instant trigger

16 © 2000 Directed Electronics, Inc. Vista, CAH1/10 BROWN (+) SIREN OUTPUTConnect this wire to the red wire of the siren. Connect the black wire of th

© 2000 Directed Electronics, Inc. Vista, CA 17plug-in harnessesThe LED operates at 2V DC. Make sure the LED wires are not shorted to ground because th

18 © 2000 Directed Electronics, Inc. Vista, CAoperation mode settingsARMING AND DISARMING WITH THE OEM TRANSMITTERWhen connected to the vehicle’s data

© 2000 Directed Electronics, Inc. Vista, CA 19NOTE: Factory content theft deterrent (CTD) systems in Bonnevilles, Auroras and LeSabres do notmonitor t

2 © 2000 Directed Electronics, Inc. Vista, CAWhat Is Included . . . . . . . . . . . . . . . . . . . . . 3Product Description . . . . . . . . . . . . .

20 © 2000 Directed Electronics, Inc. Vista, CAinternal programming jumpers To access the jumper, open the control module. This jumper is used to deter

© 2000 Directed Electronics, Inc. Vista, CA 21LEVEL II SECURITY MODEWhen this jumper is moved to the Level II position, the databus interface module w

22 © 2000 Directed Electronics, Inc. Vista, CAsystem features learn routineThe System Features Learn Routine dictates how the unit operates. It is pos

© 2000 Directed Electronics, Inc. Vista, CA 235. Release the Valet/program switch.ONCE THE FEATURE IS PROGRAMMED Other features can be programmed. T

24 © 2000 Directed Electronics, Inc. Vista, CA4 DOOR TRIGGER INSTANT/DELAYED: In the instant (default) setting, if a door is opened while the security

© 2000 Directed Electronics, Inc. Vista, CA 25table of zonesWhen using the diagnostic functions, use the Table of Zones to determine which input has t

26 © 2000 Directed Electronics, Inc. Vista, CA Closing the door triggers the system, but opening the door does not: Have you correctly identified the

© 2000 Directed Electronics, Inc. Vista, CA 27

© 2000 Directed Electronics, Inc. Vista, CA 3what is included The control module (see diagram) A Revenger®Soft Chirp®siren The plug-in Valet®/progr

4 © 2000 Directed Electronics, Inc. Vista, CAproduct descriptionThis unit is used to enhance a vehicle’s original equipment from manufacturer (OEM) fa

© 2000 Directed Electronics, Inc. Vista, CA 5AFTER THE INSTALLATION Test all functions. The “Using Your System” section of the Owner’s Guide is very

6 © 2000 Directed Electronics, Inc. Vista, CA Point the siren down so water does not collect in it. Never put the control module in the engine compa

© 2000 Directed Electronics, Inc. Vista, CA 7This system has Remote Valet, so the user can enter and exit Valet Mode without having to reach theValet/

8 © 2000 Directed Electronics, Inc. Vista, CAIf the Failsafe®Starter Kill Relay or its connections are immediately visible upon removal of the underda

© 2000 Directed Electronics, Inc. Vista, CA 9How to find (+)12V ignition with your multimeter:1. Set to DCV or DC voltage (12V or 20V is fine).2. Atta